Free HP HP0-Y37 Exam Dumps Questions & Answers

Click the Exhibit button and view the four exhibits.

You are replacing your Cisco distribution layer switches with HP E8212 zl switches. The Cisco switches have a VLAN map applied to VLAN 10 (subnet 10.1.10.0/24). The configuration for this VLAN map is as follows:

The exhibits display possible configurations for the HP ProVision ASIC-based E-Series switch. Which configuration controls traffic that arrives on VLAN 10 in the same way that the current Cisco switches do?

• A.  Exhibit 3
• B.  Exhibit 1
• C.  Exhibit 4
• D.  Exhibit 2

Click the Exhibit button and view a network diagram and three switch configurations.

You are in the process of replacing Cisco switches at the distribution layer with HP E-Series switches. You have removed one of the Cisco distribution switches so that only one remains in the network. You have also connected one HP E-Series switch in that switch's place. As shown in the network topology exhibit, the HP E-Series switch connects to the distribution layer, the edge, and the core.To eliminate network loops, the Cisco switches implement Rapid Per-VLAN Spanning Tree Plus (Rapid PVST+), and the HP E-Series switch implements Multiple Spanning Tree Protocol (MSTP). (Each connection to the core is a member of a single VLAN that is reserved for that connection and does not participate in the spanning tree.)The exhibit includes configurations for all three switches. Assume that if you do not see a command, the switch is using the default setting for that parameter. You are now ready to migrate Edge1 so that it is connected to the HP E-Series switch only.

What happens when you disable P1 on Edge1?

• A.  Link 2 only becomes active after the error state clears because VLANs 10 and 20 were in a loopback state before you disabled P1.
• B.  Link 2 comes up in all VLANs after several seconds because P2 on Edge1 is not configured with uplinkfast.
• C.  Link 2 comes up in all VLANs after a few seconds when the HP E-Series opens its P2.
• D.  Link 2 comes up almost immediately in all VLANs when Edge1, which behaves as if configured with uplinkfast, stops blocking P2.

Click the Exhibit button and view the three exhibits.



Network 16.2.0.0 /16 is advertised by Router 1 and Router 2 into BGP. All traffic from AS-65002 destined to 16.2.0.0 /16 enters AS 65001 via the Serial 3 interface of Router 1. The administrator prefers that this traffic enter AS 65001 via interface Serial 4 of Router 2. Which configuration change is most likely to achieve the desired results?

• A.  Router-1#Router-1# route-policy PolicyB permit node 20 if-match ip-prefix Prefix2 apply cost 6000 route-policy PolicyB permit node 100 Router-2# route-policy PolicyB permit node 20 if-match ip-prefix Prefix2 apply cost 7000 route-policy PolicyB permit node 100
• B.  Router-1# route-policy PolicyA permit node 20 if-match ip-prefix Prefix2 apply cost 3000 route-policy PolicyA permit node 100 Router-2# route-policy PolicyA permit node 20 if-match ip-prefix Prefix2 apply cost 2000 route-policy PolicyA permit node 100
• C.  Router-1# route-policy PolicyA permit node 20 if-match ip-prefix Prefix2 apply cost 6000 route-policy PolicyA permit node 100 Router-2# route-policy PolicyA permit node 20 if-match ip-prefix Prefix2 apply cost 7000 route-policy PolicyA permit node 100
• D.  Router-1# route-policy PolicyB permit node 20 if-match ip-prefix Prefix2 apply cost 3000 route-policy PolicyB permit node 100 Router-2# route-policy PolicyB permit node 20 if-match ip-prefix Prefix2 apply cost 2000 route-policy PolicyB permit node 100

In a LAN equipped fully with Cisco switches, you want to remove Cisco Discovery Protocol (CDP) and replace it with Link Layer Discovery Protocol (LLDP). What should you check before proceeding? (Select two.)

• A.  whether IP phones are connected to the switches and if they support LLDP-MED
• B.  whether multicast is supported on the switches
• C.  whether routing is disabled on the Cisco switches
• D.  whether the switches support LLDP/CDP Compatibility mode
• E.  whether the Cisco IOS of all switches support LLDP

Click the Exhibit button.

You are replacing your Cisco distribution layer switches with HP A-Series switches. The Cisco switches have a VLAN map applied to VLAN 21 (subnet 10.2.21.0/24). The following is a configuration for this VLAN map:

The exhibits display possible configurations for the HP A-Series switch. Which configuration controls traffic that arrives on VLAN 21 in the same way that the current Cisco switches do?

• A.  Exhibit 3
• B.  Exhibit 1
• C.  Exhibit 4
• D.  Exhibit 2