Join the discussion
Question 1/58
In a traditional campus network design using a three-tier hierarchical model, what are the key attributes of the Core layer in this model?
Correct Answer: A
Add Comments
- Other Question (58q)
- Q1. In a traditional campus network design using a three-tier hierarchical model, what are the...
- Q2. Which username and password authentication methods do Dell EMC Campus networking switches ...
- Q3. A network administrator is setting up several stacks in their network that includes differ...
- Q4. Which Dell EMC N-Series models are ideal for data center aggregation and core tiers, provi...
- Q5. Refer to the Graphic. (Exhibit) A network administrator has created a MAC ACL to allow Hos...
- Q6. Refer to the Graphic. (Exhibit) If the switches are configured for RSTP-PV, which ports wi...
- Q7. Which Dell EMC N-Series switch models can have up to 12 of the same switch model in a stac...
- Q8. If Client B sends a packet to Client A, what is the highest level of the network hierarchy...
- Q9. Which technology is designed to protect against a default gateway failure and downtime in ...
- Q10. An administrator is attempting to configure MLAG on two pairs of stacked switches; however...
- Q11. What describes Layer 3 QoS?
- Q12. Which command enables Virtual Router Redundancy Protocol in Global Configuration Mode on a...
- Q13. What is the destination IP address for IPv4 VRRP keep-alives?...
- Q14. Which port security method converts existing dynamically learned MAC addresses on an inter...
- Q15. A user's workstation is connected to an IP phone that is connected to a Dell EMC N- Series...
- Q16. Which command will show the policy-based routing map applied on an interface?...
- Q17. What describes VRRP advertisements?
- Q18. What is an accurate statement about configuring a LAG on a Dell EMC N-Series switch?...
- Q19. Which decimal value is used to indicate Assured Forwarding when implementing DSCP prioriti...
- Q20. A network administrator is configuring a switch for authentication using a RADIUS server. ...
- Q21. Which spanning tree feature will prevent unnecessary timeouts from DHCP servers?...
- Q22. When configuring a Dell EMC N-Series switch for VoIP and QoS, what is one QoS setting that...
- Q23. Which command shows IPv6 adjacent devices on Dell OS6?...
- Q24. Refer to the Exhibit. (Exhibit) Switch-1(config)# radius server host 10.1.1.111 Switch-1(c...
- Q25. N4032F#show interfaces status (Exhibit) N4032F#show interfaces port-channel 1 (Exhibit) Ha...
- Q26. In order to alter a packet's routing direction, which packet layers can policy-based routi...
- Q27. The exhibit represents a topology with all Dell EMC N4000 Series switches with RSTP enable...
- Q28. When configuring a Layer 2 MAC ACL on a Dell EMC N-Series switch, what is the default MAC ...
- Q29. Which type of an attack is considered MAC poisoning?...
- Q30. Which AAA method is only used for 802.1x and never returns an error?...
- Q31. What is the maximum power that a Class 4 PoE device can consume?...
- Q32. What are key features of the Dell EMC N4064 or N4064F switches?...
- Q33. A user's host with an IP address of 172.16.1.22/24 is attempting to FTP a file from the se...
- Q34. Which OSPF router type connects one or more Areas to the Backbone Area?...
- Q35. In a PoE environment, which IEEE protocol does a device use to request a power class?...
- Q36. In the VRRP configuration between two switches, switch A is configured with priority 150 a...
- Q37. How can a network administrator determine which Dell PowerSwitch N-Series switches can be ...
- Q38. A Dell EMC N3048P with two power supplies is configured for Class-Based Power Management. ...
- Q39. Which technologies can be implemented when configuring policy-based routing?...
- Q40. A network administrator added a new Dell EMC N-Series switch into their network with RSTP ...
- Q41. A network administrator configured two Dell EMC N-Series switches with a 2-port port-chann...
- Q42. A customer is upgrading their campus network Access layer switches. They require 2-10GbE u...
- Q43. Which Layer 2 network protocol is used for automatic configuration of switch VLANs and dyn...
- Q44. How does the weighted Queue Scheduler prioritize packets?...
- Q45. Which command sets the Expedited Forwarding bit on all matched traffic?...
- Q46. What is the Administrative Distance of static routes on a Dell PowerSwitch N-Series switch...
- Q47. Which command configures OSPF to advertise the network 10.10.0.0/16 to the Backbone Area?...
- Q48. Which two are true about discovery protocols on the Dell N-Series Voice VLAN feature? (Sel...
- Q49. You are tasked with deploying a single Dell EMC N-Series switch with a 2-port port-channel...
- Q50. If a VRRP Master router is rebooted, what is the default behavior once it comes back onlin...
- Q51. A router from a different AS is advertising a route to Area 0. How will the network route ...
- Q52. To which destination MAC address are MLAG peer-keepalive packets sent?...
- Q53. Which command enables routing in DNOS 6?
- Q54. The switch interface used for the connection to an FTP server is configured with an IP ACL...
- Q55. When using LLDP for configuration communication, what additional protocol features should ...
- Q56. A network administrator wants different applications' traffic to take different network pa...
- Q57. What is the purpose of VRRP Authentication?
- Q58. A group of four switches are configured to be part of a VRRP group with the following conf...
